Articles in "Hardware Sensors" Category

13 article(s) found in this category.
  • What should I use to protect my X-ray device from electrical surges

    What should I use to protect my X-ray device from electrical surges?Amperage Protection: First we recomend having a PowerVar* unit which will assist with protection from over Amperage.Most NEW devices sold after 2014 will come wtih the appropriate device. However if your machine did not come wtih a PowerVar unit We recommend that you contact your d...

    CONTINUE READING
  • Can I use Vatech Software on Mac Based system?

    No, our software and drivers do not work on a Mac. We also do not support VMware, PixiE boot, Dual boot, or Virtual Windows. There are too many incompatibilities with the Mac hardware when being utilized in a Windows environment.It is recommended that you use a PC based system; which you can export images to shared network storage location for impo...

    CONTINUE READING
  • What is the best way to clean Ezsensor

    In order to prevent infection, wipe the front plate of the sensor unit with ethanol or glutaraldehyde solution to disinfect it each time a different patient uses the instrument. If you plan to use a disinfectant other than those specified above, or you are mixing another disinfectant with ethanol, please consult a specialist because it may damage t...

    CONTINUE READING
  • Do you recommend using a cone indicator?

    Vatech does recommend that you use a cone indicator with this product.Cone indicators will allow you to properly position the sensor in the patient’s mouth for each desired capture mode, without damaging the cord or sensor. It is much more comfortable for the patient and allows for optimal positioning of the tube head.Damage to the cord due t...

    CONTINUE READING
  • Will my Ezsensor work on Mac?

    No, our software and drivers do not work on a Mac. We also do not support VMware, PixiE boot, Dual boot, or Virtual Windows. There are too many incompatibilities with the Mac hardware when being utilized in a Windows environment.

    CONTINUE READING
  • I received a new sensor do I need to keep the packaging?

     **it is very important to retain the installation CD in a SAFE place. In the event you need to reinstall or install the sensor in a new location you will need this disk! It contains specific Calibration files for your sensor!**We also recommend that you retain in a safe place the packaging that your sensor came with, all parts, labels, paperw...

    CONTINUE READING
  • Preventive Maintenance Schedule

    Vatech Recommends your dealer technician access the following link to download the general PM schedule. Preventive Maintenance Schedule.PDF

    CONTINUE READING
  • Can my unit be upgraded to use EzDent-i and Ez3D-i?

    Platform 2 (NEXGen Devices)All Listed Units are supported for upgrade to EZDent-i for 2D/3D units and Ez3D-i for all 3D Units*Pax-iPax-i3DPax-i3D GreenSmart3DEzSensor MultiEzSesnor-PreimiumEzSensor- HD*upgrade for Easydent4 sites are not included in lifetime updates. Please contact your local Vatech Rep for more information about upgrading to NEXGe...

    CONTINUE READING
  • What should I use to clean and Sanitize my X-ray unit; covers and accessories?

    Vatech America does not recommend or endorse any cleaning product in particularly. It is the responsibility of the practitioner to determine what is adequate for use to clean and sanitize based on FDA as well as local codes.However based on performance and recommendation by Vatech Users ; Clorox Brand* Hydrogen peroxide wipes. (Contains no bleachin...

    CONTINUE READING
  • Windows 8/10 Upgrade

    All Listed Units are considered "Legacy" and are non -supported for Windows 8/10. Ewoo  Legacy UnitsPicasso TrioPicasso DuoPicasso Master3D/Master3Ds(non Picasso) Master3D/Master3DsAnySensor (all sizes) Vatech Legacy UnitsPax500Pax P&PPaxPrimo* (LCD TYPE)PaxFlexPaxFlex3DPaxUni , PaxUni3D (all FOV's and versions*)Pax...

    CONTINUE READING